Cartridge Filter

Product Details:

Other Details:

• Wound Filter Cartridges are manufactured using a high speed, continuous wind process which creates a superior one-piece filter with hundreds of diamond shaped tunnels that get progressively smaller from the outer diameter to the core. Finer particles are progressively trapped as fluid travels to the center of the filter allowing for much greater retention capacity than straight surface filter media of same dimensions & porosity.
• The double O-ring sealing system ensures positive sealing of the filter cartridge within the housing and virtually eliminates and potential for bypass. The all polypropylene construction provides excellent chemical compatibility in a wide variety of process streams.

Advantages:

• True Depth filtration
• High Solids holding capacity
• Wide chemical compatibility
• A broad range of media and center core options provide excellent compatibility with a variety of fluids.
• Removal ratings from 1 to 20μm
• High efficiency but low in price for equipment installation & cost saving
• Fits into most standard housings
• Graded pore structure for efficient removal of a wide range of particle size

Technical Specification:

• Micron Rating: 0.5, 1, 3, 5, 10, 25, 50, 100, 150 μ
• Length: 10”, 20”, 30”, 40”
• Inner Diameter Standard: 28 mm
• Outer Diameter Standard: 64 mm
• Outer Diameter Jumbo Cartridge : 100 – 110 mm
• Configuration: Double Open End (DOE), Code 7(226 O’ Ring Flat and Bayonet Design), Code 3(222 O’ Ring Flat and Bayonet Design)

Material of Construction:

• Filter media: 100% Polypropylene fiber / Micro Glass-fibre/ Cotton
• Support media: Polypropylene fiber
• Inner core: Polypropylene cage/ Stainless steel for cotton wound
• End Caps: Polypropylene
• ‘O’ Rings/Gaskets: Silicone/ EPDM/ Viton

Application: 

• Organic Acids
• Alkalis
• Solvents
• Chemical industries
• Food & Beverage
• Electronic Industry
• Potable liquids 
• Oils

Product Details:

Other Details:

• Thermally bonded polypropylene spun filter cartridge utilize graded density media that is well suited for clarification & pre filtration applications where high particle removal is essential. The all-propylene construction provides excellent thermal & chemical compatibility with high & low pH chemicals. Also the graded density design efficiently captures contaminants throughout the media matrix resulting in excellent contaminant holding capacity, increased lifetime & low pressure drop.

Advantages:

• High flow rates and low pressure drops
• Wide chemical compatibility
• Particles removed through the entire depth of filter cartridge.
• Graded density structure for maximum dirt holding capacity
• Supported core for overall strength
• Thermal bonding process stops media migration
• Contains no resin binders, solvent, wetting or antistatic agent.

Technical Specification:

• Micron Rating: 0.5, 1, 3, 5, 10, 25, 50, 100 μ
• Length: 10”, 20”, 30”, 40”
• Inner Diameter Standard: 28 mm
• Outer Diameter Standard: 64 mm
• Outer Diameter Jumbo Cartridge: 100 – 110 mm
• Operating Temperature: 80° C
• Configuration: Double Open End (DOE), Code 7(226 O’ Ring Flat and Bayonet Design), Code 3(222 O’ Ring Flat and Bayonet Design)

Material of Construction:

• Filter media: 100% Polypropylene fiber
• Support media: Polypropylene fiber
• Inner core: Polypropylene cage
• End Caps: Polypropylene
• ‘O’ Rings/Gaskets: Silicone/ EPDM/ Viton

Application:

• Pharmaceutical Industry
• RO treatment of water
• Color & Dyes Industry
• Chemical Industry
• Water Treatment Industry
• Textile industry

Product Details:

Other Details:

• Polypropylene pleated filter cartridges have been designed as an effective membrane pre-filters and as final polishing filters for many liquid processing applications. The cartridges are double layered filters. The graded porosity design removes particles in sequence such as larger particles by the more open outer layers and the smaller particles by the tighter inner layers. The outer layer acts as the pre-filter while the inner layers provide the rating at the specified pore size. This efficiently spreads the contaminants throughout the media matrix resulting in superior contaminant holding capacity, lifetime & pressure drop as compared to other media cartridges.

Advantages:

• Very good for pre filtration & Clarification of fluids
• Graded porosity polypropylene Media.
• 100% PP construction, wide chemical compatibility.
• Consistent & good flow rates.
• Biologically safe
• No fiber migration
• FDA approved
• Thermally welded construction
• End connections to fit all standard housings

Technical Specification:

• Micron Rating: 0.2, 0.5, 1, 3, 5, 10, 25, 50, 70 μ
• Length: 10”, 20”, 30”, 40”
• Inner Diameter Standard: 28 mm
• Outer Diameter Standard: 64 mm
• Operating Temperature: 80° C
• Configuration: Double Open End (DOE), Code 7(226 O’ Ring Flat and Bayonet Design), Code 3(222 O’ Ring Flat and Bayonet Design)

Material of Construction:

• Filter media: 100% Polypropylene fiber
• Support media: Polypropylene fiber
• ‘O’ Rings/Gaskets: Silicone/ EPDM/ Viton

Application:

• Pharmaceuticals
• Food and Beverage
• Chemical Industry
• Water Treatment Industry
• Metal Finishing
• Electronics

Product Details:

Other Details:

• PTFE Absolute rated membrane cartridges are highly retentive hydrophobic or hydrophilic membrane filters that have been specially designed for critical applications. The PTFE membrane Cartridge in an all-propylene construction provides excellent chemical compatibility and superior flow per surface area as compared to other membrane cartridges.
• PTFE cartridge is ideally suited for aggressive chemicals such as acids, bases & solvents. It gives superior flow & pressure drop characteristics for gas filtration & tank venting applications. Are 100 % integrity tested with good particle removal efficiency at 0.1 & 0.2 microns.

Advantages:

• Hydrophobic PTFE membrane, prevents moisture in venting and wet air filtration.
• PTFE cartridge has excellent chemical resistance and maximum chemical compatibility.
• Higher flow rates with lesser pressure drop
• Free from binders since end caps are thermally sealed.
• Absolute rated
• Steam Sterilizable  

Technical Specification:

• Micron Rating: 0.1, 0.2, 0.45, 1 μ
• Length : 4”, 10”, 20”, 30”, 40”
• Inner Diameter Standard: 28 mm
• Outer Diameter Standard: 69 mm
• Operating Temperature: 100° C
• Configuration: Double Open End (DOE), Code 7(226 O’ Ring Flat and Bayonet Design),Code 3(222 O’ Ring Flat and Bayonet Design)

Material of Construction:

• Filter media: 100% PTFE membrane
• Support media: Polypropylene fiber
• Inner Core: Polypropylene
• Outer Core: Polypropylene
• End Caps : Polypropylene
• ‘O’ Rings/Gaskets : Silicone/ EPDM/ Viton/Buna-N

Application:

• Pharmaceutical industry
• Vent filtration
• Sterilization of inlet and exhaust flow
• Nitrogen gas filtration
• Strong acids and base filtration
• Sterile filtration of compressed air
• Electronic industry

 

Product Details:

Other Details:

• SS Pleated filter cartridges are the perfect choice for high temperature (250°C & above) & high viscosity applications. MOC is SS 304 or SS 316 or SS 316L. They offer excellent reliability for critical applications and have high dirt holding capacity. The cartridges are designed for cleanable and reusable applications so as to eliminate frequent cartridge change out.

Advantages:

• 100% Stainless steel
• Superior chemical compatibility
• Excellent mechanical strength
• High Thermal tolerance
• High dirt holding capacity

Technical Specification:

• Micron Rating: 0.2, 0.5, 1, 3, 5, 10, 25, 50, 75, 100 μ
• Length: 10”, 20”, 30”, 40”, and customizable lengths
• Inner Diameter Standard: 28 mm and customizable
• Outer Diameter Standard: 64 mm and customizable
• Operating Temperature: 250° C
• Configuration : Double Open End (DOE), Code 7(226 O’ Ring Flat and Bayonet Design), Code 3(222 O’ Ring Flat and Bayonet Design), 1” BSP Threaded

Material of Construction:

• Filter media: SS304/SS316
• Support media: SS304/SS316
• ‘O’ Rings/Gaskets: Silicone/ EPDM/ Viton/Buna-N

Application:

• Corrosive gas & liquid filtration
• Steam filtration
• Beverage industry
• Solid catalyst recovery
• Filtration of slurry oil
• Filtration of petrochemical products
• High temperature gas filtration
• Vent Application

Product Details:

Other Details:

• Stainless Steel sintered powder filter cartridges are recommended for the filtration of air or liquid at higher operating temperatures & corrosive environment. Sintered S.S. cartridges are produced by cold isostatic pressing, which gives high porosity to the material and also stability. They can easily be cleaned or back washed thus having longer shelf life. Sintered filters are able to withstand high differential pressure across the filters.

Advantages:

• High mechanical strength & good integrity
• Good corrosion and thermal resistance
• No possibility of media migration
• Good permeability
• Service life can be prolonged by cleaning and regenerating process

Technical Specification:

• Micron Rating: 0.2, 0.5, 1, 3, 5, 10, 25, 50, 75, 100 μ
• Length: 10”, 20”, 30”, 40”, and customizable lengths
• Inner Diameter Standard: 28 mm
• Outer Diameter Standard: 64 mm
• Operating Temperature: -200°C to1000°C
• Configuration: Double Open End (DOE), Code 7(226 O’ Ring Flat and Bayonet Design), 1” BSP Threaded

Material of Construction:

• Sintered Polypropylene
• Sintered Polystyrene
• Sintered Ceramic
• Sintered Polyethylene

Application:

• Gas & liquid filtration
• Solid catalyst recovery
• Filtration of slurry oil
• Filtration of petrochemical products
• High temperature gas filtration
• Vent applications
• Chemical reagents

Product Details:

Other Details:

• Polyethersulfone (PES) absolute rated membrane cartridges are inherently hydrophilic and contain no added surfactants or wetting agents that could alter the taste in beer, wine, bottle water & other beverages. PES absolute filters are sterile filters offering superior flow characteristics, high contaminant holding capacity and consistent removal of particles and microorganisms. The cartridges are 100% integrity tested to assure reliability.

Advantages:

• Provide broad chemical compatibility.
• Extremely high flow rates at low pressure drops
• PES is permanently hydrophilic membrane
• Cost effective for a variety of aqueous based liquids.
• No adhesives, binders or surfactants.
• Reduces downtime & improves throughput.
• Meets ASTM bacterial validation standards

Technical Specification:

• Micron Rating: 0.05, 0.1, 0.2, 0.45, 1.
• Length: 10, 20, 30, 40.
• Inner Diameter Standard: 28 mm
• Outer Diameter Standard: 64 mm
• Operating Temperature: 80 C
• Configuration: Double Open End (DOE), Code 7(226 O Ring Flat and Bayonet Design), Code 3(222 O Ring Flat and Bayonet Design)

Material of Construction:

• Filter media: 100% PES Hydrophilic membrane
• Support media: Polypropylene fiber
• 'O' Rings/Gaskets: Silicone/ EPDM/ Viton

Application:

• End point filtration in variety of processes like
• Bottle and process water
• Beer, wine & beverages
• Serum & blood based products
• Cell & tissue culture media
• Diagnostics
• Microbiological growth media
• Antibiotics
• Vaccine preparation

Product Details:

Other Details:

• Pleated dust collector filters are one of the most advanced innovations in dust collector technology in decades. These are made up of 100% Spun Bonded polyester media with different coatings on it, as per requirement of applications. With a host of advantages over traditional bag and cage technology, pleated filters deserve the attention of all dust collector operators. In many cases, it is possible to retrofit older pulse jet dust collectors to use pleated filters.

Advantages:

Increased filter area
Low pressure drop 
Abrasion resistance 
Improved filter efficiency 
Ease of maintenance 
Leak proof design 

Technical Specification:

• Length: 500mm, 1000mm, 1400mm, 2000mm
• Standard Diameter: 160 mm

Material of Construction:

Filter Media: Spun Bonded Polyester media/ Pleated PPS Media/ Nomex Media
Top/Bottom Cap: EPDM, Natural Rubber, polyurethane and metal caps

Application:

Pharmaceuticals
Steel & Power
Powder coating
Shot Blasting
Cement
Chemicals
Metals & Minerals
Paints & Pigment